Key fob and remote repairs in Perth
A key fob or garage remote is a small circuit board with buttons, a battery and a radio transmitter. When it stops working, the fault is often in those electronics rather than the car or the door. PC FIX-IT does key fob repairs. Tell Mark what the remote is for and what it does when you press a button.
Ask about this serviceHow Mark helps
Tell Mark what's happening
Call or send a message in your own words. You don't need the technical name.
Agree the plan and cost first
Mark asks a few questions, explains the options and quotes the job. Work starts once you approve the quote.
Fixed, checked and explained
Mark does the agreed work and checks with you before doing anything extra. Before he finishes, he goes over the result with you, so you know what was fixed.
Why a car key fob or remote stops working
Common key fob faults are general to most remotes. Battery contacts go flat or corrode and lose their grip on the battery. Buttons wear through with use, so one press works and the next does not. Cases crack after drops. Solder joints break where a battery holder or button meets the board. Liquid damage corrodes the board, sometimes long after the fob dried out.
Each fault looks a little different. A remote that works only when squeezed points to a loose contact or cracked joint. One dead button with the others working points to that button. A fob that stopped after a wash or a rain soaking points to liquid damage.
Remote not working? Try a fresh battery first
Start with a new battery of the type printed on the old one. Batteries in remotes can last a long time, so a flat one is easy to forget. Fit it the right way up, following the marking in the holder, and check that the contacts touch it firmly.
If a spare fob or remote exists, try it. When the spare works, the fault is probably in the first remote. When neither works, the car, gate or door receiver may be the problem, and that belongs with whoever services it.
What to send for a key fob repair
Send the make and model of the car, gate or garage door, plus any model number on the remote. Add photos of the outside, the battery compartment and any crack or damage. Say what happens when you press each button, whether a light shows, and when the problem began.
Mention a drop, a wash, a rain soaking or an earlier repair attempt. If the case is already open, keep every part together, including the rubber button pad and any small metal key blade.
Garage remote repair and gate remotes
Garage and gate remotes fail in the same ways as car fobs: worn buttons, poor battery contacts, cracked cases and broken joints. Tell us the brand and model of the opener as well as the remote. If several remotes for the same door have all stopped, the opener is more likely to be the cause than the remotes.
A replacement remote may need to be paired or coded to the opener. That step follows the opener maker's instructions or the installer's service, so check what your system needs before replacing a remote.
Limits of a key fob repair
Repair covers the remote's electronics and case. PC FIX-IT does not cut key blades and does not code a fob to a vehicle. That work belongs with an auto locksmith or the dealer, and a transponder chip that needs replacing may be theirs too. Ask before you book, so you know who should handle each part.
Not every fob can be repaired. A board with heavy corrosion or a failed chip that cannot be replaced may need a new remote instead. You will hear what the assessment finds before any further work is agreed.
Broken solder joints inside a fob are covered on the soldering and circuit board repairs page. A cracked case may suit a 3D printed replacement part, depending on the design and its rights.
What customers say
Mark was able to fix my l/top overnight, very happy with the service, and he took the time to explain it all...
No runaround, no upselling, just straight-up honest work. They told me what was wrong, fixed it, and didn’t charge an arm and a leg.
Service was prompt and fixed the problem with both my laptop and PC within half an hour. Mark was lovely to deal with and explained things in an easy to understand manner.
Rated 4.7 on Google from 12 reviews. Read all reviews on Google
Arrange help and check the cost
Tell us your suburb, the equipment involved and what you need working. Onsite help is on demand or by booking. Check our service areas and discuss availability before making plans.
Every job is quoted individually. Tell us what needs fixing and we will discuss the options and cost before you go ahead. See how a job works.
Same-day, next-day and urgent call-outs available. Travel fees may apply for locations more than one hour from Perth CBD. Confirm the scope and total cost before work starts.
