Perth Hills based · Perth metro & beyondCall 0431 253 588

Soldering and circuit board repairs in Perth

Some faults live on the circuit board itself. A charging port that only works at an angle, an HDMI port that lost its picture or a wire that snapped off a joint all need solder work. PC FIX-IT does soldering and circuit board repairs as bench work. Tell Mark the device, the fault and what happened first.

Ask about this service

How Mark helps

  1. Tell Mark what's happening

    Call or send a message in your own words. You don't need the technical name.

  2. Agree the plan and cost first

    Mark asks a few questions, explains the options and quotes the job. Work starts once you approve the quote.

  3. Fixed, checked and explained

    Mark does the agreed work and checks with you before doing anything extra. Before he finishes, he goes over the result with you, so you know what was fixed.

How a job works, step by step

Charging port, DC jack and HDMI port repairs

Ports and connectors take strain every time a cable goes in or comes out. A worn or cracked connector can lose contact, and the solder joints holding it to the board can crack. That is why a charger may work only when the plug is held a certain way. Laptop DC jacks, USB charging ports and HDMI ports all fail like this.

Console HDMI ports are a common example. A cable pulled sideways or a console moved while plugged in can damage the port or lift it from the board. Tell us the console or laptop model, which port is affected and whether the picture or charge comes and goes or has stopped altogether.

Broken solder joints, wires and component replacement

Other solder work covers a wire that has broken off a board, a joint that has cracked with heat or movement, and a component that has failed and needs replacing. Switches, buttons and small connectors inside a device are often soldered in place too. Describe the symptom in your own words, even if you are not sure which part has failed.

Motherboard repair and other board-level faults need an assessment before anyone can say whether a repair is practical. A replacement part has to be available and suit the board. Some faults turn out to be several problems at once. You will hear what the assessment finds before any further work is agreed.

What to send before a soldering repair

Send the make and model, ideally from the label. Add a clear photo of the outside and a close photo of the damaged port or area. Explain what happened: a drop, a spill, a cable pulled sideways, a power surge or a fault that grew over time. Mention any earlier repair attempt, because old solder work changes what the board needs.

You do not need to open the device to make an enquiry. If it is already open, keep every screw and part together and say so. Keep private information out of the photos, including anything shown on the screen.

How the assessment works, and its limits

Solder work is not done during a home visit. The device is assessed as bench work first. That decides whether a soldering repair suits the fault, which parts are needed and what it will cost. Nothing further is attempted until you have agreed the scope and the total.

Not every board can be repaired. Damaged traces, liquid corrosion, unavailable parts or a fault spread across the board can make a repair impractical or uneconomical. Some devices are better handled by the manufacturer, especially under warranty. Stop using anything with a burning smell, a swollen battery or a damaged power connection, and tell us about it when you call.

Files on the device and the handover

If the laptop, console or drive holds files or saves you need, say so before any work is planned. Getting a board working and protecting the data are separate questions. Board work can be the route to the files, or it can put them at risk. Discuss both before agreeing to a repair.

Our Swan View postal address is not a walk-in workshop, so please arrange any handover in advance. Ask which charger, cable or accessory should come with the device. At the handover, check the repaired port or function together with the cable or charger you normally use.

A cracked case, clip or bracket near the repair may suit a 3D printed replacement part. A remote or car key that has stopped working has its own page for key fob and remote repairs.

What customers say

Mark was able to fix my l/top overnight, very happy with the service, and he took the time to explain it all...

Vaughan G., Google review

No runaround, no upselling, just straight-up honest work. They told me what was wrong, fixed it, and didn’t charge an arm and a leg.

Liam L., Google review

Service was prompt and fixed the problem with both my laptop and PC within half an hour. Mark was lovely to deal with and explained things in an easy to understand manner.

Nadine A., Google review

Arrange help and check the cost

Tell us your suburb, the equipment involved and what you need working. Onsite help is on demand or by booking. Check our service areas and discuss availability before making plans.

Every job is quoted individually. Tell us what needs fixing and we will discuss the options and cost before you go ahead. See how a job works.

Same-day, next-day and urgent call-outs available. Travel fees may apply for locations more than one hour from Perth CBD. Confirm the scope and total cost before work starts.

Call 0431 253 588Get help